HO CHI MINH CITY JOURNAL OF MEDICINE
banner
Nghiên Cứu Y Học

SO SÁNH ĐỘ KHÍT SÁT CỦA SƯỜN ZIRCONIA CHO MÃO TOÀN SỨ VỚI SƯỜN KIM LOẠI CHO MÃO SỨ-KIM LOẠI

COMPARISON OF FIT OF ZIRCONIA COPING TO ALL-CERAMIC CROWN WITH METAL COPING TO METAL-CERAMIC CROWN

Bấm tải bài viết

Tạp chí Y học Thành phố Hồ Chí Minh, 14(1):349. DOI

Lượt xem: 291 Lượt tải PDF: 15

Tác giả

Nguyễn Khánh Mỹ, Hoàng Tử Hùng

Tóm tắt

Mục tiêu của nghiên cứu này là so sánh độ khít sát ở các thành (thành trục và thành mặt nhai) và ở vùng đường hoàn tất của sườn sứ zirconia cho mão toàn sứ với sườn kim loại cho mão sứ-kim loại. 
Phương pháp nghiên cứu: nghiên cứu in vitro được thiết kế dựa theo phương pháp của Chang (2004) và Beuer (2008). Từ một cùi răng khô của răng cối nhỏ thứ nhất hàm trên, lấy dấu bằng cao su và đổ mẫu bằng thạch cao cứng. Mười mẫu được chia làm 2 nhóm, mỗi nhóm 5 mẫu: Nhóm 1: thực hiện 5 sườn zirconia bằng hệ thống Cercon 2.2 (Denstply). Nhóm 2: thực hiện 5 sườn Ni-Cr bằng phương pháp đúc truyền thống. Gắn sườn phục hình vào cùi răng thạch cao tương ứng bằng cao su lỏng. Dùng đĩa cắt kim cương cắt qua sườn phục hình và cùi răng thạch cao theo chiều ngoài-trong. Đo độ dày lớp cao su (ở thành mặt nhai, thành trục và vùng đường hoàn tất) dưới kính hiển vi quang học chuyên dùng (Olympus GX51) mỗi vùng đo tại 14 điểm (đơn vị tính µm).
Kết quả: (1) Độ khít sát ở các thành (thành trục và thành mặt nhai) của sườn zirconia lần lượt là 73,61 ± 4,80µm và 75,53 ± 21,25µm, của sườn Ni-Cr lần lượt là 74,73 ± 14,82µm và 99,20 ± 38,03µm, sự khác biệt không có ý nghĩa với giá trị p lần lượt là 0,82 và 0,10; p>0,05. (2) Độ khít sát ở vùng đường hoàn tất của sườn Ni-Cr (78,67 ± 31,23µm) cao hơn có ý nghĩa so với sườn zirconia (121,21 ± 11,90µm) (p=0,01; p<0,05), nhưng đều nằm trong khoảng lâm sàng chấp nhận được. (3) Trung bình độ khít sát của sườn zirconia là 90,12 ± 10,08µm và sườn Ni-Cr là 84,20 ± 22,01µm, sự khác biệt không có ý nghĩa (p=0,45; p>0,05).
Kết luận: trung bình độ khít sát của cả hai nhóm trong khoảng giá trị chấp nhận được trên lâm sàng (<100µm).

Abstract

Purpose: the aim of this in vitro study was to compare the marginal and internal (axial and occlusal) fit of zirconia coping to metal coping. 
Materials and Methods: ten stone dies were fabricated from one extracted maxillary right first premolar. They were randomly divided into 2 groups of 5 dies each. Group 1: 5 zirconia copings fabricated with Computerized-assisted design (CAD)/Computerized-assisted manufacturing (CAM) system (Cercon, Denstply). Group 2: 5 Ni-Cr copings were prepared on dies using conventional lost-wax casting technique. The inner surface of the copings was filled with the light body material. The copings were then placed onto the stone dies. After embedding, the copings were sectioned bucco-lingually. The obtained sections were measured at occlusal, axial, and marginal locations under specialized light microscope (Olympus GX51). The fit was measured as the thickness of the light body impression material at the measuring points. This resulted in forteen measurements at each location, making 84 measurements for each replica. A total of 840 measurements were made. The Student's paired t test was used to detect significant differences between zirconia coping - stone die and Ni-Cr coping - stone die misfits.
Results: the mean gap widths of the zirconia coping were 75.53µm at the occlusal location; 73.61µm at the axial wall; 121.21µm at the margin; and 90.12µm in total. The mean gap widths of the Ni-Cr coping were 99.20µm at the occlusal location, 74.73µm at the axial wall; 78.67 at the margin; and 84.20 in total. There were no differences in internal (axial, occlusal) fit among the two groups. Although the marginal fit of the coping Ni-Cr was significantly smaller than the zirconia coping, the values obtained were clinically satisfactory. In conclusion, the fit of the zirconia coping was not significantly different from the Ni-Cr coping. 
Conclusion: the mean marginal gaps of the two groups were within the range of clinically acceptable values (<100µm).